EXACTLY HOW TO INSTALL A BATH TUB YOURSELF

Exactly How to Install a Bath Tub Yourself

Exactly How to Install a Bath Tub Yourself

Blog Article

Book Now

Are you currently trying to find selective information on How to Install a Bathtub Yourself?


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually qualified on your own for the work and are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your tools and material checklist must make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.

    Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted access that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
    Before carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Installing the Bath tub


    Using both wooden boards under its feet, put the bath tub in the required position. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
    The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reads level.
    To set up faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other faucet.
    Activate the supply of water and also examine all joints and new pipework for leakages and tighten them if required. Fill up the bath tub and likewise check the overflow electrical outlet and also the normal outlet for leaks.
    Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the tub needs to wait till the bathtub has been utilized at the very least when as this will settle it into its last placement.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next off, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the supplier given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split rather early if you do not take into consideration this activity before sealing.
    Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I recently found that piece on How to Install a Bathtub Yourself while doing a lookup on the internet. Sharing is good. Helping others is fun. I cherish reading our article about Tools You Need to Install a New Bathtub .




    Apply Now


    Report this page